Ghost Controls Keypad & Intercom Repair Nationwide

Ghost Controls Keypad & Intercom Repair: The Katy Owner’s Guide

Ghost Controls keypad and intercom repair in Katy typically runs between $190 and $410 installed, depending on whether we’re replacing the keypad membrane, the intercom board, or both. We keep common Ghost Controls keypad and intercom parts on the truck, so a single visit usually gets your entry panel working again. Most owners discover the problem in the same way: a code that works sometimes but not always, or an intercom that lets visitors talk but not press buttons, or the classic Texas summer failure, which is a sun-baked keypad face that won’t register digits.

Call (346) 818-3319

Which Ghost Controls Models This Applies To

Ghost Controls has shipped a few different entry-panel styles since the company hit the residential gate market, and the keypad on a 2018 AXP opener is not the same part as the keypad on a current TSS1 or R Series package. The quickest way to identify what you have: open the keypad face and look for the two-letter date code printed on the back of the membrane, or check the model tag inside the main control box. If that tag is gone, we match by connector type. Older Ghost Controls keypads use a 4-pin screw terminal; newer units use a 6-pin plug-in harness. That’s the sort of detail that prevents ordering the wrong part twice. We’re an independent service provider, not affiliated with Ghost Controls, which means we can install either OEM Ghost Controls parts or a quality aftermarket equivalent when it makes sense. For keypads specifically, the OEM membrane tends to last longer in UV than the budget aftermarket lines, so we default to OEM unless availability forces otherwise.

Signs Your Ghost Controls Keypad & Intercom Repair Is Failing

• Some digits work, some don’t. The contact under the membrane wears unevenly. The numbers you use most, usually the ones in your code, die first. That’s a membrane replacement, not a wiring problem.
• The keypad works fine in the morning but stops in the afternoon. Heat expansion is the culprit. Katy summers push panel surface temperatures past 140 degrees, and old solder joints on the board flex until they crack. It cools, contracts, and works again the next morning.
• Visitors can hear you through the intercom but you can’t hear them. Ghost Controls intercoms use a separate speaker wire run. When the microphone side fails, the speaker is usually fine. That’s a board-level repair, not a bad wire.
• You enter the code, the gate beeps, and nothing moves. The keypad is fine and the relay on the intercom board is not closing. We test this in 30 seconds with a multimeter before selling you a part you don’t need.
• Water intrusion or condensation behind the faceplate. The gasket fails, or the enclosure wasn’t sealed properly at install. Once moisture hits the board, corrosion follows within a season.

Before

After

Replacement Cost & What’s Included

The installed price range above covers parts and labor, and we hand you a written price before a single screw comes out. A basic Ghost Controls keypad swap with a new OEM membrane usually lands between $190 and $260. If the intercom board is gone too, you’re looking at $320 to $410. The spread depends on whether your model uses the older screw-terminal harness or the newer plug-in style, and whether the housing is still watertight or needs a replacement enclosure. You get the part number on the written record, a photo log of the old part removed and the new part installed, and the 365-Day Done Right Promise on the entire job. That means if anything isn’t right for a full year, we make it right at no additional charge.

DIY or Call Us?

What’s safe to check on your own: confirm the code you’re entering matches the code on the gate opener (we see a lot of keypads that are fine and codes that were changed during a power outage), look for obvious water in the housing, and confirm the wiring at the panel is tight. What goes wrong in DIY: the control board runs on low voltage, so the electrical hazard is minimal, but the harness connectors on Ghost Controls boards are easy to crack if you pull at the wrong angle, and we’ve replaced more than one board that died from a homeowner shorting two pins while trying to “test” it. If you’d rather have us look at it, call (346) 818-3319 and we’ll get a technician out with the parts on hand.

FAQs