Linear Gate Installation Nationwide

Linear Gate Installation in Katy: What to Know First

Linear gate installation in Katy typically runs $900 to $2,800 for a complete residential swing or slide gate with a new Linear actuator, and most jobs are finished in one day once the gate and operator are on site. We are an independent Linear service provider, not a factory dealer, which means we install the brand because your property is already set up for it, not because we get a commission. This page is for Katy homeowners who own a Linear motor, a Linear gate frame, or a Linear remote system and need the installation done without guesswork. If you already know the model, tell us when you call (346) 818-3319 – it saves a trip.

Call (346) 818-3319

How Linear Products Fail and How We Fix Them

Linear makes a wide range of gate operators, and a few specific issues repeat themselves in Katy subdivisions from Cinco Ranch to Firethorne. Here is what we actually find when a Linear system needs installation or reinstallation.

• Linear LDO50 / LDO33 swing-arm actuator drift. The LDO50 is a 24V swing gate operator common on single-family driveway gates in Katy. Its known weak point is the limit cam assembly. When the cam wears, the gate starts closing short by an inch, then two, then six. Homeowners notice the gate never quite seats. We reset the cams, and if the cam teeth are stripped, we replace the cam block rather than the whole actuator. That is a $40 part instead of a $700 motor.
• Linear APeX controller board capacitor failure. The APeX series control boards run hot in Texas summers. When the main capacitor degrades, the gate opens fine but fails to auto-close. That is the board, not a safety-eye problem. On installation or reinstallation, we bench-test the board first so you do not pay for a photo-eye replacement that does not fix the symptom.
• Linear SLR slide gate operator chain tension loss. On sliding gates, Linear SLR models throw a fault when the chain tensioner backs off even slightly. Katy’s clay soil shifts with rain and drought, which moves the gate post enough to loosen the chain. We reset chain tension to manufacturer spec and re-anchor the post if it has moved more than half an inch.
• Linear MDR / Megacode receiver range collapse. When a Linear receiver stops reading remotes beyond 15 feet, the usual cause is a corroded antenna wire where it enters the control box. We have seen this so often in Katy’s humid months that we check the antenna connection on every Linear job, reinstallation or not. A $6 splice beats a $180 receiver swap.
• Linear gate frame corrosion at the bottom hinge. Linear brand gate frames from the early 2010s used powder coat over mild steel. Katy’s humidity and occasional flooding wear the coating at the hinge weld first. If you are installing a new Linear opener on an older Linear frame, we inspect the hinge weld before mounting the actuator. Installing a motor on a hinge that is about to tear out costs more later.

Our Linear Gate Installation Process

1. 1
   You call, you get a person. No voicemail queue. You describe the gate, the site, and whether the operator is already on the property or needs to be ordered. We tell you over the phone whether it sounds like installation, reinstallation, or repair-and-install.
2. 2
   We run the site check. A technician comes out and measures the gate leaf, confirms the Linear model, checks the mounting surface and electrical run, and photographs the mounting points. You get a written price before any tool comes out of the truck. No exceptions.
3. 3
   Parts decision, in writing. If a part is needed, we give you the OEM price and a quality aftermarket option where one exists. On Linear actuators, the OEM gear and arm assemblies are worth the money. On remotes and receivers, aftermarket Megacode-compatible parts work identically and cost less. You choose, in writing.
4. 4
   The install. We mount the operator, set the limits, align the photo-eyes, dial in the force settings, and run the gate through a full open-close cycle test at least four times. If it binds in either direction, we fix the bind before we leave; we do not just raise the force setting.
5. 5
   Programming and handoff. We program your existing Linear remotes and keypads into the new operator, or add new Megacode remotes if yours are dead. Then we run the obstruction test together so you see the gate reverse.
6. 6
   The paper trail. Before we leave, you get a photo log of every adjustment and a written record of the part numbers installed. That is clause 4 of the Haven Standard – Evidence on every job. If a future technician ever opens that box, they will know exactly what we did, when, and with what part.

Before

After

What Linear Gate Installation Costs in Katy

Straight numbers, because vague pricing wastes your afternoon. Here is what we see across Katy.

• Basic single swing gate with new Linear LDO50 actuator, existing gate frame in good shape: $950 to $1,400 installed, programmed, and tested, including written documentation.
• Double swing gate (two leaves, two actuators or one plus a mechanical link): $1,800 to $2,800. Double gates need matched actuator timing or the leaves collide. Cheaper installs skip this step and you notice within a week.
• Slide gate with new Linear SLR operator on existing track: $1,200 to $2,200 depending on track condition and run length.
• Installation-only (you already have the Linear operator, still in the box): $500 to $900 depending on mounting surface, conduit run, and programming scope.

What moves the price: the mounting surface (brick column vs. steel post vs. concrete pad), the distance from the nearest outdoor outlet or conduit, and whether the gate frame hinges and posts are sound enough to accept the new operator. We tell you the number before we start, not after. Call (346) 818-3319 and we will give you a written quote. Estimates are free.

Why Katy Homeowners Call Vance Gate Repair Katy for Linear Work

Adrian Vance started doing gate work in 2014 on commercial access-control sites, where the rule was: write down what you found, what you fixed, and what the customer should check next. He brought that habit to Katy residential work, and it is why our Linear jobs get documented like a commercial install. We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if a Katy property has a mixed setup – Linear opener on the driveway, Ghost Controls keypad on the pedestrian gate – one call covers it. Every Linear installation is covered by the 365-Day Done Right Promise. If the install is not right, we make it right within a year, no argument and no additional fee.

FAQs