Linear Gate Repair Nationwide

Linear Gate Repair in Katy: What to Know First

Linear gate repair in Katy typically runs between $185 and $650 depending on whether the fault is in the operator, the gate hardware, or the safety loop system. Most Linear repair jobs we handle are completed in a single visit because we carry the common Linear control boards, limit assemblies, and receiver modules on the truck. If your Linear opener is dead, drifting, or reversing for no reason, this page tells you what’s actually wrong and what it costs to make it right.

Call (346) 818-3319

This page is for Katy homeowners with a Linear swing or slide gate operator who want the problem diagnosed correctly the first time. Call (346) 818-3319 and a live person answers, any hour.

How Linear Products Fail - and How We Fix Them

Linear operators show up all over Katy, especially in subdivisions built between 2005 and 2015. Here are the failure patterns we see most often on service calls, named by the series and the actual cause.

• Linear LSO and LDO swing operators: limit switch drift. The LSO series uses mechanical limit cams that slowly walk out of position as the gate cycles. The gate starts slamming into the open stop or stopping six inches short of closed. We reset the limits, then photograph the new setting and note it in the job record so the next adjustment doesn’t start from zero.
• Linear MegaCode receivers: phantom open failures. The MegaCode receiver (commonly paired with ACT-31B or ACT-34B keypads) occasionally picks up interference from nearby 318 MHz devices. The gate opens on its own, which owners often mistake for a bad board. We swap the receiver to a shielded position or replace it, then test across all remotes before leaving.
• Linear APeX and VS-GSL slide operators: blown motor capacitors. Slide gates in Katy heat run long cycles, and the start capacitor in APeX/VS-GSL units takes the wear. The symptom is a humming operator that won’t move. We test capacitance on-site, replace with the correct microfarad rating, and verify the start winding draws within spec.
• Linear control boards (ACR, XK, or APeX logic): relay failure after lightning. Katy storms cook relay contacts on the open and close circuits. The board still powers up, but the gate won’t respond or only moves one direction. We verify with a meter before condemning the board, because a lot of companies replace the board when the real fault is a fried accessory wired into the same terminal block.
• Linear photo-eye misalignment on double swing gates. The photo-eye (the infrared beam that stops the gate if something crosses the path) gets knocked out of line by gate frame flex or yard work. The gate refuses to close or reverses mid-travel. We realign the beam, verify alignment at both full-open and mid-travel positions, and secure the mounting bracket so the next brush with a mower doesn’t undo the job.

Our Linear Gate Repair Process

1. 1
   Listen and document. You tell us what the gate is doing. We write it down exactly as you describe it. That symptom list is our diagnostic starting point.
2. 2
   Diagnose on-site. The technician opens the control box and tests, not guesses. Meters on the board, limit readings, capacitor checks, photo-eye alignment. Every reading is recorded.
3. 3
   Present the written price. Before any tool touches a part, you get the scope and the flat price in writing. You approve it, or we shake hands and charge you nothing for the diagnosis. That’s Haven Standard Clause 1: have it in writing.
4. 4
   Repair with honest parts decisions. If the fault is a Linear board or motor, we quote OEM where replacement matters for function. If an aftermarket part performs identically and carries a comparable service life, we tell you the price difference and let you choose.
5. 5
   Test and document. We cycle the gate through full travel in both directions, trip the safety edges and photo-eye, and test every remote and keypad. Photos are taken of the repair, the settings, and the finished job. You get a copy. We keep one in the file.
6. 6
   Leave it clean and covered. The work area is left clean, the gate operates, and the 365-Day Done Right Promise applies to the repair. If it’s not right, we make it right, no argument, no fee.

Before

After

What Linear Gate Repair Costs in Katy

Here’s what Katy homeowners should expect for common Linear repair scenarios. These are flat ranges, not hourly estimates. The price is fixed before work starts.

What moves the price: whether the board is still available from Linear or needs a quality aftermarket equivalent, whether the gate frame is square enough to reset limits properly, and whether the damage includes secondary parts like the arm bracket or keypad wiring. You get the exact number in writing before we touch anything. Estimates are free. Call (346) 818-3319.

Why Katy Homeowners Call Vance Gate Repair Katy for Linear Work

We’re an independent Linear service provider, not a factory authorized shop. That matters because we have no incentive to steer you toward a full operator replacement when a $220 board swap fixes the gate. Adrian Vance carried a documentation habit out of commercial access-control work that most residential gate companies never adopted: every visit ends with a written record of what we found, what we fixed, and what you should watch for. You get a photo log. We keep a copy for the next technician, even if that technician isn’t us.

We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. So if your property has a Linear on one gate and a different brand on the other, one company handles both. A live person answers the phone 24 hours a day, seven days a week. The technician dispatched to your Katy home has a name, a background check, and a photo that we send before arrival. The repair carries the 365-Day Done Right Promise: one full year, no argument, no fee.

FAQs